Toll Free: +1 (800) 523-7867
|

Stop It® Pipe Repair System

XCorr® Flat Patch

XCorr® Flat Patch - Leak Sealing

XCorr® Flat Patch is a carbon-epoxy composite repair system designed for sealing applications where localized repair is needed or full pipe wraps are impractical. XCorr® Flat Patch utilizes a premeasured 2-part novolac epoxy system combined with triaxial carbon fiber reinforcement fabrics and a technical felt to provide superior leak sealing capacity on flat surfaces. XCorr® Flat Patch is recommended for pressure applications up to 1,500 psi (105 kg/cm2) with a built in 4:1 safety margin. Return to service at pressure may be accomplished in ~5 hours for temperatures above 75°F.

Attributes

  • Novolac epoxy resin yields exceptional chemical resistance, 100% solids, No VOCs
  • Cartridge dispensing minimizes waste, ensures complete mixing, and manages pot life
  • Primary technical felt layer ensures interfacial wetting and highest pressure performance
  • Outstanding compressive, flexural, and adhesive bond strength
  • Accelerated cure times are possible with annealing of the installed repair
  • Carbon fiber composite repair system safely and quickly restores operations up to 1,500 psi, and provides localized corrosion inhibition

XCorr® Flat Patch
XCorr® Flat Patch upclose

XCorr® Flat Patch Properties

Resin at 75°F (24°C)*

Mixing Ratio: 3:1

Pot Life: 35 minutes

Dry To Touch: 4 hours

Full Mechanical Strength: 24 hours

Full Chemical Resistance: 24 hours

*Pot life is greatly reduced with increased mixing volume and temperature. Cure time is significantly extended at lower temperature.

Composite

Repair Thickness: 0.15 in

Lap Shear Adhesion: 1,320 psi (ASTM D 3165)

Dry Adhesion: >3,000 psi (ASTM 4541)

Wet Adhesion: >3,000 psi, 5 days 158°F (70°C) water (ASTM 4541)

Sealing Pressure: 1,500 psi, based on patch repair of 0.125” od hole in flat steel plate

Compressive Strength: 10,000 psi (ASTM C109)

Shore D Hardness: 84 (ASTM D 785)

Temperature/Heat Resistance: From -20°F up to 350°F (-29°C to 177ºC) –continuous, dry. Consult chemical compatibility to gauge wet service perfomance.

Part No Description Case Quantity Case WT
(lbs)
XCFP XCorr Flat Patch, 10″ x 10″ 1 5
XCorr® Flat Patch – Dispenser Gun Sold Separately
DG600M Dispenser Gun – Dual Component, Manual, 600 mL 1 4

XCorr® Flat Patch Specifications

Packaging: Resin supplied in dual cartridge (parts A and B packaged separately) with pre-measured volumes sized. Kits provided with static mixers, spreaders and gloves. Two-part dispensing guns sold separately.

Sizes: Patch size- 10″ x 10″

Shelf Life: Part A: 12 months at 75°F (24°C). Part B: 12 months at 75°F (24°C)

Storage Temperature: 32 to 100°F (0 to 43°C), 0-100% relative humidity

Application Temperature: 50 to 150°F (10 to 65°C)

Surface Preparation: Surfaces must be cleaned of all oil and debris and dried. For metal surface, a bright metal finish is desired (SSPC-SP10 (immersion) or SSPC-SP6 (non-immersion)).

Complete the form below to request documents.

* Indicates Required Selection

"*" indicates required fields

Please select each product for which information is being requested. Multiple products may be selected at the same time. Documents will be immediately forwarded by email.
For which products are you requesting documents? (select all that apply)*

close-link
error: Content is protected !!