Stop It® Pipe Repair System

Roll-Over Kit F

Leak Sealing Products

Roll-Over Kit F

Covers a large hole, crack, or gash in a large vessel or tank with a patch that conforms to the curvature of the vessel. The patch uses a variety of T-bolts to support itself directly to the hole. The leak is then sealed by tightening the compression bolts around the frame, conforming the patch to the vessel.

Series “F” contains one stainless-steel patch measuring 13” x 23” with 3/4” neoprene gasket. One stainless-steel support frame with compression bolts, three stainless-steel T-bolts with preassembled wingnut washer combos, all necessary tools and heavy-duty carrying case.

Shelf Life: Two years from date of purchase when stored at 40° to 83°F (5° to 28°C)
Color: White or black
Tensile Strength: 24,950 PSI / in width/172 MPa
(ASTM D 3039).

Flexural Strength: 12,005 psi/82.77 MPa (ASTM 790)
Durometer Hardness: 63 (Shore D) (ASTM D 2240)
Pressure Retaining Capability: Recommended for pressures up to 400 psi (28 kg/cm2)
Temperature Resistance: Continuous: -20° to 250°F (-29° to 121°C)
Intermittent: 250° to 500°F (121° to 260°C)
Set Time: 3 to 5 minutes at 50° to 80°F (10° to 27°C)
Cure Time: at 1/2`` thick (1.27 cm) - 30 minutes

Part Number:
White/Black Stop It® Pipe Repair System Size
Packaged 10 per ctn Weight
Lbs/Kgs
24786 / 24257 2`` x 4' / 5.08cm x 1.2m 4 / 1.8
21278 / 21225 2`` x 12' / 5.08cm x 3.6m 6 / 2.7
41278 / 41225 4`` x12' / 10.16cm x 3.6m 8 / 3.6
42578 / 42525 4`` x25' / 10.16cm x 7.62m 14 / 6.3

The Stop It® Pipe Repair System has been subjected to intensive testing and complies with US DOT 49CFR parts 192 and 195, and ASME PCC-2 article 4.1.

Compatibility
Generally, Stop It® may be used with products that are compatible with polyurethane plastic. The end user must always determine the suitability of the product for its intended use and recognize that the durability of the repair may be affected by strong acids or bases.

Stop It® Pipe Repair System Data Sheets

Chemical Resistance
No visible changes in Stop It® after an immersion term of 35 days in the following chemicals:

Acetic Anhydride Ammonia
Ammonium Hydroxide (10%)
Decyl Ammonium Chloride
Diesel Fuel
Diethyl Ether
Ethyl Acetate
Ethyl Ether
Ethylene Glycol
Gasoline

Hydrochloric Acid (10%)
Lube Oil
4-Methyl 2-Pentanone
Mineral Spirits
Sodium Hydroxide (50%)
Sulfuric Acid (10%)
Sulfuric Acid (25%)
Varsol
Xylenes, Mixed o-, m- and p

Potable Water
The Fix Stix Epoxy included with each kit is certified to NSF/ANSI 61 for Drinking Water.

Safety Features
Even under extreme pressures, the Stop It® Pipe Repair Tape will not shatter or crack. Stop It® releases pressures slowly.

When tested to the failing point in laboratory conditions, failure was indicated by a reduction in line pressure and seepage.

Complete the form below to request documents.

All fields are required.
close-link